Disciplines > Test > Introduction

Click here for more information about Test and Evaluation. Click here to see concepts related to Test and Evaluation. Click here for an overview of the workflow in the Test and Evaluation discipline. Click here for an overview of the activities in Test and Evaluation. Click here to see artifacts used in Test and Evaluation. Click here to see guidelines related to Test and Evaluation.

In Module 0 read  Intorduction to Testing: Purpose and Relation to Other Disciplines to begin the course.  The Concepts will be analyzed in the other Modules.

Concepts

Purpose To top of page

The Test discipline acts in many respects as a service provider to the other disciplines. Testing focuses primarily on the evaluation or assessment of quality realized through a number of core practices:

  • Finding and documenting defects in software quality.
  • Generally advising about perceived software quality.
  • Proving the validity of the assumptions made in design and requirement specifications through concrete demonstration.
  • Validating the software product functions as designed.
  • Validating that the requirements have been implemented appropriately.

An interesting but somewhat subtle difference between Test and the other disciplines in RUP is that testing is essentially tasked with finding and exposing weaknesses in the software product. For this effort to be successful, this necessitates a somewhat negative and destructive rather than constructive approach. The challenge is to avoid both an approach that does not suitably and effectively challenge the software and expose it's inherent problems and weaknesses, and an approach that is so destructive that it will likely never find it possible to consider the quality of the software product acceptable.

Based on information presented in various surveys and essays, software testing is said to account for 30 to 50 percent of total software development costs. It is therefore perhaps surprising to note that most people believe computer software is not well tested before it is delivered. This contradiction is rooted in a few key issues.

First, testing software is enormously difficult. The different ways a given program can behave are unquantifiable. Second, testing is typically done without a clear methodology so results vary from project to project, organization to organization: success is primarily a factor of the quality and skills of the individuals. Third, insufficient use is made of productivity tools, making the laborious aspects of testing manageable: in addition to the lack of automated test execution, many test efforts are conducted without tools that allow the effect management of extensive Test Data and Test Results. While the flexibility of use and complexity of software makes complete testing an impossible goal, a well-conceived methodology and use of state-of-the-art tools, can help to improve the productivity and effectiveness of the software testing.

For "safety-critical" systems where a failure can harm people (such as air-traffic control, missile guidance, or medical delivery systems), high-quality software is essential for the success of the system. For a typical MIS system, the criticality of the system may not be as immediately obvious, but it's likely that the impact of a defect could cause the business using the software considerable expense in lost revenue or possibly legal costs. In this "information age", with increasing demand on provision of electronically delivered services over the Internet, many MIS systems are now considered "mission-critical"; that is, companies cannot fulfill their functions and experience massive losses when failures occur.

A continuous approach to quality, initiated early in the software lifecycle, can significantly lower the cost of completing and maintaining the software. This greatly reduces the risk associated with deploying poor quality software.

Relation to Other Disciplines To top of page

The Test discipline is related to other disciplines.

  • The Requirements discipline captures requirements for the software product, and those requirements are one of the primary inputs for identifying what tests to perform.
  • The Analysis & Design discipline determines the appropriate design for the software product; this is the another important input for identifying what tests to perform.
  • The Implementation discipline produces builds of the software product that are validated by the Test discipline. Within an iteration multiple builds will be tested, typically one per test cycle.
  • The Environment discipline develops and maintains supporting artifacts that are used during test, such as the Test Guidelines and Test Environment.
  • The Management discipline plans the project, and the necessary work in each iteration. Described in an Iteration Plan, this artifact is an important input to defining the correct evaluation mission for the test effort.
  • The Configuration & Change Management discipline controls change within the project team. The test effort verifies that each change has been completed appropriately.


Copyright  © 1987 - 2001 Rational Software Corporation


Display Rational Unified Process using frames

Rational Unified Process